Heidenhain iTNC 530 (34049x-08) Manuale Utente Pagina 691
- Pagina / 739
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
HEIDENHAIN iTNC 530 691
18.1 General user parameters
List of general user parameters
External data transfer
Adjusting TNC interfaces EXT1 (5020.0) and
EXT2 (5020.1) to an external device
MP5020.x
7 data bits (ASCII code, 8th bit = parity): Bit 0 = 0
8 data bits (ASCII code, 9th bit = parity): Bit 0 = 1
Block Check Character (BCC) any: Bit 1 = 0
Block Check Character (BCC) control character not permitted: Bit 1 = 1
Transmission stop through RTS active: Bit 2 = 1
Transmission stop through RTS inactive: Bit 2 = 0
Transmission stop through DC3 active: Bit 3 = 1
Transmission stop through DC3 inactive: Bit 3 = 0
Character parity even: Bit 4 = 0
Character parity odd: Bit 4 = 1
Character parity undesired: Bit 5 = 0
Character parity desired: Bit 5 = 1
Number of stop bits that are transmitted at the end of a character:
1 stop bit: Bit 6 = 0
2 stop bits: Bit 6 = 1
1 stop bit: Bit 7 = 1
1 stop bit: Bit 7 = 0
Example:
Use the following setting to adjust the TNC interface EXT2 (MP 5020.1) to
an external non-HEIDENHAIN device:
8 data bits, any BCC, transmission stop through DC3, even character
parity, character parity desired, 2 stop bits
Input for MP 5020.1: %01101001
Interface type for EXT1 (5030.0) and
EXT2 (5030.1)
MP5030.x
Standard transmission: 0
Interface for blockwise transfer: 1
Touch probes
Selecting signal transmission MP6010
Touch probe with cable transmission: 0
Touch probe with infrared transmission: 1
Probing feed rate for triggering touch
probes
MP6120
1 to 3000 [mm/min]
Maximum traverse to first touch point MP6130
0.001 to 99 999.9999 [mm]
Safety clearance to probing point during
automatic measurement
MP6140
0.001 to 99 999.9999 [mm]
- User’s Manual 1
- HEIDENHAIN 1
- Conversational Format 1
- Controls of the TNC 2
- About this manual 5
- About this manual 5
- Software options 7
- Intended place of operation 10
- Legal information 10
- 340422-xx/340423-xx 11
- Changed functions in version 18
- 34049x-06 18
- 34049x-02 27
- 34049x-03 28
- 34049x-04 29
- 34049x-05 30
- 34049x-07 32
- 34049x-08 33
- Contents 35
- 2 Introduction ..... 85 38
- HEIDENHAIN iTNC 530 57 57
- 17 MOD functions ..... 645 59
- First steps with the 63
- 1.1 Overview 64
- 1.2 Machine switch-on 65
- The most important TNC keys 66
- Defining a workpiece blank 68
- Program layout 69
- Programming a simple contour 70
- Creating a cycle program 73
- Starting the test run 78
- 1.5 Tool setup 79
- 1.6 Workpiece setup 81
- 1.7 Running the first program 84
- 2.1 The iTNC 530 86
- 2.2 Visual display unit and 87
- Setting the screen layout 88
- Operating panel 89
- 2.3 Operating modes 90
- 2.4 Status displays 100
- 2.5 Window manager 103
- 2.6 Accessories: HEIDENHAIN 104
- HR electronic handwheels 105
- 106 Introduction 106
- Programming: 107
- Fundamentals 107
- 3.1 Fundamentals 108
- Conversational 113
- Define the blank: BLK FORM 113
- Creating a new part program 114
- Actual position capture 118
- Editing a program 119
- The TNC search function 123
- 3.3 File management: 125
- Data backup 126
- Directories 127
- Calling the file manager 130
- Copying a single file 135
- Copying a table 137
- Copying a directory 138
- Deleting a file 139
- Deleting a directory 139
- Tagging files 140
- Renaming a file 142
- Additional functions 143
- Working with shortcuts 145
- Archiving files 146
- Extracting files from archive 147
- The TNC in a network 150
- Programming aids 153
- 4.1 Adding comments 154
- 4.2 Structuring programs 156
- 4.3 Integrated calculator 157
- 4.4 Programming graphics 158
- 4.5 3-D line graphics 160
- (FCL2 function) 160
- Block number display ON/OFF 162
- Erasing the graphic 162
- Displaying error messages 163
- Display HELP 163
- Function 164
- Showing the error list 164
- Window contents 165
- Generating service files 167
- Working with the TNCguide 169
- Programming: Tools 175
- Feed rate F 176
- Spindle speed S 177
- 5.2 Tool data 178
- 5.3 Tool compensation 211
- Programming contours 217
- 6.1 Tool movements 218
- 6.3 Contour approach and 223
- APPR LCT 228
- 6.4 Path contours—Cartesian 231
- Straight line L 232
- Corner rounding RND 234
- Radius R 237
- Direction of rotation DR 237
- Miscellaneous function M 237
- Feed rate F 237
- 6.5 Path contours— 244
- Polar coordinates 244
- Straight line LP 245
- Helical interpolation 248
- Example: Helix 251
- Initiating the FK dialog 256
- Pole for FK programming 257
- Input possibilities 258
- Auxiliary points 262
- Relative data 263
- Example: FK programming 1 265
- Example: FK programming 2 266
- Example: FK programming 3 268
- Programming: Data 271
- 7.1 Processing DXF files 272
- (software option) 272
- Opening a DXF file 273
- Basic settings 274
- Layer settings 275
- Zoom function 287
- 7.2 Data transfer from plain 288
- Subprograms and 291
- 8.1 Labeling subprograms and 292
- 8.2 Subprograms 293
- 8.3 Program section repeats 294
- Operating sequence 295
- Programming notes 295
- 8.5 Nesting 297
- 8.6 Programming examples 301
- Q parameters 307
- 9.1 Principle and overview 308
- Overview 313
- Definitions 315
- 9.4 Trigonometric functions 316
- 9.5 Circle calculations 317
- 9.6 If-then decisions with 318
- Programming if-then decisions 319
- Abbreviations used: 319
- 9.7 Checking and changing 320
- 9.8 Additional functions 321
- Entering formulas 343
- Rules for formulas 345
- Programming example 346
- 9.10 String parameters 347
- 9.11 Preassigned Q parameters 358
- 9.12 Programming examples 364
- Miscellaneous 371
- 10.1 Entering miscellaneous 372
- Smoothing corners: M90 377
- Deleting basic rotation: M143 390
- Principle 393
- Special functions 395
- Program defaults menu 397
- Menu of programming aids 399
- (FCL4 function) 404
- 11.3 Fixture monitoring 406
- (DCM software option) 406
- Fixture templates 407
- FixtureWizard 407
- Editing fixtures 410
- Removing fixtures 410
- Managing fixtures 413
- 11.4 Tool carrier management 416
- ToolHolderWizard 417
- Removing a tool carrier 418
- 11.5 Global Program Settings 419
- Technical prerequisites 421
- Shift the soft-key row 422
- Basic rotation 424
- Swapping axes 425
- Superimposed mirroring 426
- Axis locking 427
- Superimposed rotation 427
- Feed rate override 427
- Handwheel superimposition 428
- Limit plane 430
- 11.6 Adaptive Feed Control 434
- Select the TNC:\ directory 437
- Recording a teach-in cut 438
- Activating/deactivating AFC 441
- Log file 442
- Show the log file 443
- Spindle load monitoring 444
- Application 445
- Activating/deactivating ACC 445
- 11.8 Generating a backward 446
- Application example 448
- 11.10 File functions 450
- 11.11 Defining coordinate 451
- TRANS DATUM TABLE 452
- TRANS DATUM RESET 453
- Defining a program call 454
- 11.12 smartWizard 455
- 11.13 Creating text files 458
- Applications 463
- Table for workpiece materials 464
- Table for cutting data 465
- Configuration file TNC.SYS 468
- 11.15 Freely definable tables 469
- Multiple axis machining 475
- Introduction 477
- Defining the PLANE function 479
- Position display 479
- Resetting the PLANE function 480
- EULER PLANE 485
- VECTOR PLANE 487
- PLANE POINTS 489
- PLANE function 494
- Retract the tool 500
- Activate M128 500
- 12.4 TCPM FUNCTION 501
- (software option 2) 501
- Defining the TCPM FUNCTION 502
- Resetting the TCPM FUNCTION 505
- M116 (software option 1) 506
- Selecting tilting axes: M138 514
- 12.6 Three-dimensional tool 516
- DR2>0 518
- DR20.004 523
- DR2+0.002 523
- such as a surface oversize 525
- Pallet editor 531
- 13.1 Pallet editor 532
- 13.2 Pallet operation with 538
- Selecting a pallet file 543
- Exiting the pallet file 549
- Executing the pallet file 549
- Select a pallet table 550
- Manual operation and 551
- 14.1 Switch-on, switch-off 552
- 14.2 Moving the machine axes 555
- Entering values 567
- Preparation 569
- 14.5 Using touch-probes 577
- 14.6 Calibrating touch probes 582
- 14.7 Compensating workpiece 585
- Datum setting in any axis 591
- Circle center as datum 593
- Center line as datum 594
- (software option 1) 600
- Activating manual tilting 604
- Positioning with manual 607
- Test run and 613
- 16.1 Graphics 614
- 16.3 Test run 625
- 16.4 Program run 631
- 16.5 Automatic program start 641
- 16.6 Optional block skip 642
- 16.7 Optional program-run 643
- 644 Test run and program run 644
- MOD functions 645
- 17.1 Selecting MOD functions 646
- 17.2 Software numbers 648
- 17.3 Entering code numbers 649
- 17.4 Loading service packs 650
- Assignment 652
- Software for data transfer 653
- 17.6 Ethernet interface 655
- 17.7 Configuring PGM MGT 666
- 17.8 Machine-specific user 668
- Rotating the entire image 671
- 17.10 Position display types 672
- 17.11 Unit of measurement 673
- 17.13 Selecting the axes for 675
- Datum display 677
- 17.15 Displaying HELP files 678
- 17.18 Setting the system time 681
- 17.19 TeleService 682
- 17.20 External access 683
- 17.21 Host computer operation 685
- Statistics 688
- Tables and overviews 689
- 18.1 General user parameters 690
- Non-HEIDENHAIN devices 707
- RS-422/V.11 interface 708
- 18.3 Technical information 709
- Windows XP (option) 719
- 19.1 Introduction 720
- 19.2 Starting an iTNC 530 723
- 19.3 Network settings 725
- 19.4 Specifics about file 727
- Data transfer to the iTNC 530 728
- Overview tables 735
- Miscellaneous functions 737
- Touch probes from HEIDENHAIN 739
Prodotti e manuali riguardandi Apparecchiature Heidenhain iTNC 530 (34049x-08)
(751 pagine)
(748 pagine)
(785 pagine)
(529 pagine)
(527 pagine)
(529 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale